Network cable connections worksheet

During the planning process, complete the cable-connection tables with the locations of the cable connections for each control enclosure in the system.

Ethernet connections

Each node canister in the control enclosure connects over an Ethernet cable from Ethernet port 1 of the canister to an enabled port on your Ethernet switch or router. Ethernet port 1 is for accessing the management GUI, for accessing the service assistant GUI for the node canister, and for iSCSI host attachment. You can attach an Ethernet cable from Ethernet port 2 on the canister to your Ethernet network. Port 2 can be used for the management GUI and for iSCSI host attachment. Ports 3 and 4 are for iSCSI attachment only.

Note: The ports on the upper node canister (canister 1) are numbered from right to left. However, the ports on the lower node canister (canister 2) are numbered from left to right.
Figure 1. Ethernet ports on canister 1 (upper canister)
Image showing Ethernet ports on canister 1 (upper canister)
Figure 2. Ethernet ports on canister 2 (lower canister)
Image showing Ethernet ports on canister 2 (lower canister)

Ethernet cable standards

The following table provides a list of Ethernet cable standards.
Table 1. Ethernet cable standards
Ethernet port type Cable type Minimum standard Connector
1 Gbps Ethernet technician port TP Cat 5e RJ45
10 Gbps onboard Ethernet ports TP Cat 6 (up to 55 m); Cat 6a or Cat 7 (up to 100 m) at 10 Gbpsl; Cat 5e at 1 Gbps RJ45
25 Gbps Ethernet host interface adapter (must be ordered) Optical OM3 (up to 70 m); OM4 (up to 100 m) LC

Ethernet onbard ports

Record the node canister onboard Ethernet port connections in the following table.

Table 2. Node canister onboard Ethernet port connections
Node canister 1 (upper)
Component Ethernet port 4 Ethernet port 3 Ethernet port 2 Ethernet port 1 Technician port
Switch         None
Port         None
Speed (10 Gbps or 1 Gbps)         1 Gbps
Node canister 2 (lower)
Component Ethernet port 1 Ethernet port 2 Ethernet port 3 Ethernet port 4 Technician port
Switch         None
Port         None
Speed (10 Gbps or 1 Gbps)         1 Gbps

Ethernet networking adapter ports

Each node canister also supports optional 2-port 25 Gbps internet Wide-area RDMA Protocol (iWARP) or RDMA over Converged Ethernet (RoCE) Ethernet adapters. The following guidelines must be followed if 25 Gbps Ethernet adapters are installed.
  • iWARP and RoCE Ethernet adapters cannot be mixed within a node canister.
  • Fibre Channel adapters are installed before Ethernet adapters, beginning with slot 1, then slot 2, and slot 3.
  • Ethernet adapters are installed beginning with the first available slot.
  • To connect to expansion enclosures, you must order a 4-port 12 Gbps SAS adapter that is installed in slot 3. However, only ports 1 and 3 are used to establish a SAS connection.
Use the following table to record the node IP address that you intend to add to any port that is used for node-to-node RDMA communication. The node IP, subnet mask, gateway, and VLAN ID are used for node-to-node communications
Table 3. Ethernet adapter port connection worksheet
Node canister 1 Ethernet Adapter Slot 3 Ethernet Adapter Slot 2 Ethernet Adapter Slot 1
Port 10 Port 9 Port 8 Port 7 Port 6 Port 5
Switch            
Port            
Speed: 25 or 10 Gbps            
Cable type            
Node IP            
Subnet mask            
Gateway            
VLAN ID            
Node canister 2 Ethernet Adapter Slot 1 Ethernet Adapter Slot 2 Ethernet Adapter Slot 3
Port 5 Port 6 Port 7 Port 8 Port 9 Port 10
Switch            
Port            
Speed: 25 or 10 Gbps            
Cable type            
Node IP            
Subnet mask            
Gateway            
VLAN ID            

Fibre Channel connections

Each node canister supports one or two 4-port 32 Gbps FC adapters or 4-port 16 Gbps FC adapters. The adapters are installed based on the following guidelines. Use the following table to record the FC port connecttions.

  • The first Fibre Channel adapter must be installed in adapter slot 1.
  • If more Fibre Channel adapters are needed, they are installed in slots 2 and 3.
Table 4. Fibre Channel port connection worksheet
Control Enclosure S/N:
Node Canister 1 FC Adapter Slot 3 FC Adapter Slot 2 FC Adapter Slot 1
Port 12 Port 11 Port 10 Port 9 Port 8 Port 7 Port 6 Port 5 Port 4 Port 3 Port 2 Port 1
Switch, node, or host                        
Port                        
Speed: 32, 16, or 8 Gbps                        
Cable type                        
Node Canister 2 FC Adapter Slot 1 FC Adapter Slot 2 FC Adapter Slot 3
Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 9 Port 10 Port 11 Port 12
Switch, node, or host                        
Port                        
Speed: 32, 16, or 8 Gbps                        
Cable type